自動熒光定硫儀

能量色散X射線硫含量?jī)x

RX-620SA

RX-620SA determines total sulfur in petroleum products, such as gas oil, fuel oil, crude oil and naphtha, using energy dispersive X-ray fluorescence(EDXRF) method, which is an accurate, non-destructive, economical and yet quick method prescribed in ISO 8754 and ASTM D4294-03. Once a sample is set, the total sulfur is determined automatically in 300 seconds(typical). The model RX-620SA is a 12-sample carousel model. After its successful predecessors, this fourth generation has been developed to further improve the accuracy and ease of use.

RX-620SA 是按“能量色散X射線熒光光譜法（EDXRF） ”測定石油產品硫含量的儀器。可通用于車用汽油，柴油，原油，石腦油，渣油，潤滑油基礎油，液壓油，噴氣燃料和其他餾分油在內的碳?xì)浠衔镏械牧蚝繙y(cè)定。適用于ISO 8754 ，ASTM D4294-03.，GB/T 17040的標準。測試過程簡單高效，試驗結果準確和重復性良好，是一種經濟的無損測試方法。通常情況下，測試一組樣品多要300秒，RX-620SA帶有一個自動旋轉的測試盤，可連續測試12個樣品。作為“田中科學”的第四代產品，儀器性能有了進一步的提升，使用更簡單靈活。

HIGH PRECISION: Pulse height analysis(PHA) is automatically carried out before each measurement to adjust the system. This innovative system design has further improved the precision.

精度高：高精度脈沖電子計數系統，精確而高效。

WIDE RANGE OF SAMPLES: Patented “Diamond Parameter Method” accurately compensates for measurement error caused by different carbon/hydrogen(C/H) ratio of individual sample. This state-of-art technology enabled measurement of wide range of samples of different C/H ratios with uncompromising precision.

測試范圍廣：獨有的 “Diamond Parameter Method”,無論是輕油,原油,重油。從低濃度到高濃度,均能在短時間內通過簡單的操作,高精度地測出硫分值。對于不同的碳?xì)浠衔铮–/H）也能自動補正

AMBIENT TEMPERATURE AND BAROMETRIC PRESSURE COMPENSATION: Compensation for ambient temperature and barometric pressure are made automatically to drastically minimize the drift. 對于環境的影響,可通過氣壓補正,溫度補正進行自動調整。

AUTOMATIC CALIBRATION: Set certified calibration standards and start automatic calibration program to carry out automatic calibration. Either multiple point calibration at up to 12 points or two point calibration starts. 比對標準樣品，儀器可進行自動的2點校正和多點校正。

CAROUSEL TYPE SAMPLE CHANGER WITH ACRYLIC COVER: X-ray shielding is by a metallic cover moving downward on the objective sample cell. Since the acrylic dust cover is not intended for shielding X-ray, it may be opened during a test, allowing access to sample cells in the cue.

自動旋轉樣品臺：樣品測試區（X射線區）有獨立的金屬護罩獨立分隔，通過旋轉平臺一一更換，每一個樣品都是獨立測試的。即使在測試過程中也可以打開儀器外罩，更換或添加樣品，不會有X射線泄露的危險，尤其適用于大量集中連續的樣品測試。

TANAKAX-Ray Sulfur Meter, model RX-620SA

TYPE:

Total sulfur analyzer for petroleum products by energy-dispersive X-ray fluorescence method (EDXRF)

用非色散X射線熒光光譜分析法測定石油產品中硫含量

CONFORMING STANDARDS: （適用標準）

ISO 8754, ASTM D4294-03, GB/T 17040 etc.

SAMPLE CANGER:

Carousel type 12-position sample changer. Sample cells not being measured are accessible during the measurement.

12孔自動旋轉樣品臺。樣品之間獨立分隔，不受影響。

SAMPLE VOLUME: （樣品需求）

Approx. 5ml （大概5ml）

MEASURING RANGE: （硫含量測試范圍）

0-6.00wt%

REPEATABILITY: (Typical) （重復性）

Range（范圍）	Std Deviation（標準誤差）	Measuring Time（測試計數）
0.008wt%max	10ppm*	300sec x 3times（300秒測試3次）
0.05wt%max	20ppm	100sec x 3times
0.05-0.50wt%	40ppm	100sec x 3times
0.51-1.50wt%	60ppm	100sec x 3times
1.51-2.00wt%	100ppm	100sec x 3times
2.01-4.00wt%	200ppm	100sec x 3times
4.01-6.00wt%	400ppm	100sec x 3times

*: ASTM D4294 designates the repeatability in the range(r). In terms of standard deviation, 5ppm.

按ASTM D4294標準規定，標準偏差為5ppm

C/H RATIO COMPENSATION: （C/H補正誤差）

Automatic with 0.003wt% max of compensation error when a 1wt% sample is tested.

MEASURING TIME: （測試方式）

10-990sec. 1-99 times. （測試時間10-990秒，可設定重復測試 1-99 次）

CALIBRATION: （儀器標定方式）

*Automatic two point calibration automatically followed by a measurement. 自動2點標定

*Manual two point calibration手動2點標定

*Automatic multiple-point calibration(up to 12 points) 自動多點標定（多12點）

*Manual multiple-point calibration(up to 12 points) 手工多點標定（多12點）

X-RAY SOURCE: （x射線源功率）

X-ray tube rated 7KV

SAMPLE CELL: 樣品杯

2-piece Teflon cup with disposable mylar film （2個聚四氟乙烯樣品底座+一次性（Mylar）分子薄膜）

PRINTER: （打印）

Built-in impact dot matrix printer (57mm) （內置點式打印機，紙寬57mm）

DISPLAY: （顯示屏）

LCD (20 characters x 4 lines) LCD可顯示20字符，4行

DATA OUTPUT:

RS-232C 1cannel

X-RAY LEAKAGE: （x射線源外散）

0.6µSv/Hr or  less on instrument surface （經測試，儀器表面小于0.6 micro Sv/Hr）

OPARATING TEMPERATURE/HUMIDITY: （環境要求）

10-30℃ with a temperature drift within 10℃ in a day. RH to be within 80%.

室溫10～30℃(一天內的溫差變化在10℃以下) / 濕度80‰ RH以下

POWER SULLPY: （電源需求）

AC 100-240V+/-10%, 45-66Hz, 200VA

SAFETY: （安全防護）

Interlock mechanism against accidental X-ray leakage  （雙重保險設計，有效避免 x射線泄露）

DIMENSIONS/WEIGHT: 尺寸/重量

560mmW x515mmD x245mmH/ 29kg

STANDARD ACCESSORIES:（標準附件）

1.Power supply cable電源線	1
2.Sample cell holder樣品杯支架	12
3.Sample cell holder spring樣品杯簧片	12
4.Teflon sample cells樣品杯	12
5.Sample cell assembling jig樣品杯組裝工具	1
6.Sample cell disassembling jig樣品杯分解工具	1
7. Mylar sheet (200mm x 1,000m) 樣品膜（200mmX1,000米）	1卷
8. Sample cell stand樣品杯底座	1
9.Printer roll paper打印紙	3
10.Printer ink ribbon備用打印機色帶	1
11.Printing paper holder打印紙支架	1
12.Spare glass tube fuse電源保險絲	2

OPTIONAL ACCESSORIES:（推薦附件）

1. Certified Reference Material*(標定用樣品)

    Sulfur in gas oil:（輕油硫含量標定樣品）

       100, 200, 500 and 800 ppm level （ppm級）

    Sulfur in residual fuel oil: （重油硫含量標定樣品）

       0.0, 0.1, 0.2, 0.5, 1, 2, 3 and 4wt% level （質量百分?jǐn)?shù)級）

*: For a traceable calibration, the CRMs are necessary （標定儀器必須，建議必配）